.jpeg?q=90&p=thumb&w=200&h=200)
.jpeg?q=90&p=thumb&w=40&h=40)
Brakes 
Driveline 
Electronics 
Handlebars & Controls 
Package Deals 
Wheel Accessories 
Wheels by Vehicle 
Tools and Maintenance 
Universal & Repair 
Vivid Racing Gear
See more parts for BMW 340i
Select the year of your BMW 340i:
Vargas Turbocharger Technologies - VTT Single Piece Silicone Charge Pipe Non-BOV Blue BMW 340i | 440i | 540i | 640i | 740i | 840i | M140i | M240i | X3 | X4 2016-2022 VTT-B58-CP-BLUE-1 | Vivid Racing
VTT is proud to offer the very best charge pipe solution for the Toyota A90/91 Supra platforms. This system completely does away with the restrictive, and mule-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi. They are molded for the perfect fit in your Engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the Engine or ambient heat. Another huge benefit is your vehicle goes from 4 connections to only TWO which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off. This means no more blown charge pipe connections on the track or road leaving you stranded.
There are other options on the market, but they only address the problem in half measures. Some offer silicone connectors that are attached to hard pipes and are notorious for blowing, but they do nothing to address the heat soak issue or the number of connections needed. This kit solves ALL of those problems and does so at a lower cost.
Install is very easy and takes about an hour if you are inexperienced with working on your own car, can take as little as 30-45 minutes if you have had it apart a few times.
Dimensions for the pipes are as follows:
Hot Side Pipe: 64mm or 2.50″ on the connection to the turbo outlet opening up immediately to 77mm or 3″ and remaining a FULL 3″ to the throttle body inlet.
The kit includes:
Fitment:
There are other options on the market, but they only address the problem in half measures. Some offer silicone connectors that are attached to hard pipes and are notorious for blowing, but they do nothing to address the heat soak issue or the number of connections needed. This kit solves ALL of those problems and does so at a lower cost.
Install is very easy and takes about an hour if you are inexperienced with working on your own car, can take as little as 30-45 minutes if you have had it apart a few times.
Dimensions for the pipes are as follows:
Hot Side Pipe: 64mm or 2.50″ on the connection to the turbo outlet opening up immediately to 77mm or 3″ and remaining a FULL 3″ to the throttle body inlet.
The kit includes:
- VTT Hot Side Silicone Charge pipe
- 2 VTT Branded CNC adapters to mount the map sensor, and Temp Probe
- 2 VTT Branded CNC adapters for the Turbocharger outlet, and TB inlet
- 2 VTT branded T-Bolt Clamps
- 2 1/8 NPT ports are included in the TB flange for methanol
Fitment:
- BMW 340i F30 2016-2018
- BMW 440i F32 | F33 | F36 2017-2019
- BMW 540i G30 2017-2022
- BMW 640i G32 2019-2020
- BMW 740i G10 | G11 | G12 2016-2022
- BMW 840i G15 2019-2022
- BMW M140i F20 | F21 2016-2018
- BMW M240i F22 | F23 2017-2018
- BMW X3 G01 2018-2022
- BMW X4 G02 2019-2022
Proposition 65
⚠ WARNING:
Cancer and Reproductive Harm
https://www.P65Warnings.ca.gov
| Make Vehicle | Model | Year |
|---|---|---|
|
2016-2018 BMW 340i |
340i | 2016-2018 |
|
2017-2019 BMW 440i |
440i | 2017-2019 |
|
2017-2022 BMW 540i |
540i | 2017-2022 |
|
2019-2020 BMW 640i |
640i | 2019-2020 |
|
2016-2022 BMW 740i |
740i | 2016-2022 |
|
2019-2022 BMW 840i |
840i | 2019-2022 |
|
2016-2018 BMW M140i |
M140i | 2016-2018 |
|
2017-2018 BMW M240i |
M240i | 2017-2018 |
|
2018-2022 BMW X3 |
X3 | 2018-2022 |
|
2019-2022 BMW X4 |
X4 | 2019-2022 |
Check out these other great products
Error: Failed to add product
Please refresh the page and try again.